$55.00 USD
Under normal circumstances, the standard GoPro battery will last for one to two hours of shooting. The CamDo Blink controller can be programmed to turn the camera off between shots to only have the camera powered on when the footage is needed. However, while Blink can extend the length of time the camera can be deployed on a single battery, the total amount of time the camera can remain powered on is still the same. The V15 battery increases the GoPro battery life by approximately 4x and has the Always On operating mode required for use with our Blink controller.
There are a lot of battery packs available, however, don't be fooled by cheaper alternatives. Most of the USB battery packs on the market have an automatic power saving feature which turns off the battery if it is not continuously supplying power. Often, this feature is not even mentioned in the battery description, and only discovered when you find the camera's internal battery is dead, even though the high powered battery pack is still fully charged.
Calculating battery life is non-trivial. It depends on the camera model, firmware version, SD card speed, lighting conditions, battery size, age of the battery, ambient temperature, and more. To help you understand the issues and to calculate estimated battery life, consult the Camera Power Consumption Study and our Time Lapse Calculator.
Up to four V15 battery packs fit in our Weather Resistant Outdoor Enclosures and one V15 battery is included with our 6Watt Solar Power System. Up to three V15 battery packs can fit inside of our DeepEXT aluminum deepwater housing extension.
The V15 comes with all necessary cabling to parallel up with other V15 batteries including the V15 that ships with our Solar system. See the FAQ's and Support tab on this page.
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✔* |
|
HERO5 Session |
✔* |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✔ |
|
HERO (2014) |
✔ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
*Does not include USB-C cable
Compatible with 5V USB Devices.
How long will the battery last before it is discharged?
It depends on many factors: the controller you are using, the camera you are using and the shooting schedule you have programmed. There are just too many variables to give an accurate answer.
In theory, the 4,000 mAh V15 battery combined with the standard GoPro 1,050 mAh battery will give you about 5 times the shooting time.
Combine multiple V15 batteries together in parallel (you can fit 4 x V15's in our solar enclosure to provide 16,000 mAh (60 Wh)) to give you that extra shooting time.
An analysis of the power consumption of the various GoPro cameras and an explanation of how to calculate the theoretical battery life is outlined on the GoPro Power Consumption page. Our Time Lapse Calculator page can be used to assist you in planning the interval times of your time lapse project.
How do I connect multiple V15 batteries together?
Additional V15 batteries can be ordered for use with our Solar and weatherproof enclosures (4 x V15's can fit in our enclosure) for extra shooting time. All of the wiring to connect them together comes with the batteries. It just a simple matter of plugging them together as per our guide here.
How many V15 batteries can fit in the solar or DRY weatherproof enclosures?
Up to 4 x V15's can fit in either the Solar or weatherproof DRY enclosure. It just a simple matter of plugging them together as per our guide here.
How can I tell when the battery is in Always On mode?
It is easiest to determine the operating mode when the battery is disconnected and neither charging or supplying power to a device. When in Always On mode, if you double tap the power button a few times, the LED should continue to stay lit. If the LED goes dark between every other double press, you are not in Always On mode.
How can I change the operating mode?
To switch modes, hold down the power button for six seconds.
If you are not in the desired mode. Press the button again for 6 seconds to change modes.
General support can be found on our Support pages here.
Average GoPro recording times in each video setting (limited by battery capacity)
Also read the FAQ's tab for more information.
Product Code: BAT04
$14.50 USD $29.00 USD
Product Code: ASD02
The 32GB microSDHC 633x Class 10 UHS-I Memory Card from Lexar features a maximum read speed of 95MB/s along with a minimum transfer rate of 10MB/s (U1 is rating not recommended for use with HERO3+ and newer cameras). This Class 10 UHS-I card is supplied with a USB 3.0 card reader for high-speed file transfer to your computer.
CamDo recommends these U3 rated 1000x SD cards.
$139.00 USD
Under normal circumstances, the standard GoPro HERO4 battery will last for one to two hours of shooting. The Blink or BlinkX can be programmed to turn the camera off between shots to only have the camera powered on when the footage is needed. However, while Blink can extend the length of time the HERO3+ and HERO4 cameras can be deployed on a single GoPro battery, the total amount of time the camera can remain powered on is still the same. The V44 battery increases the GoPro battery life by approximately 11x and has the Always On operating mode required for use with our Blink and BlinkX controllers.
BlinkX requires an external power source and cannot be powered directly from the GoPro battery.
There are a lot of battery packs available, however, don't be fooled by cheaper alternatives. Most of the USB battery packs on the market have an automatic power saving feature which turns off the battery if it is not continuously supplying power. Often, this feature is not even mentioned in the battery description, and only discovered when you find the camera's internal battery is dead, even though the high powered battery pack is still fully charged.
Calculating battery life is non-trivial. It depends on the camera model, firmware version, SD card speed, lighting conditions, battery size, age of the battery, ambient temperature, and more. To help you understand the issues and to calculate estimated battery life, consult the Camera Power Consumption Study and our Time Lapse Calculator.
Up to two V44 battery packs fit in our Weather Resistant DryX/SolarX Outdoor Enclosures and one V44 battery is included with our SolarX Enclosure.
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 Black |
✔* |
|
HERO5 Session |
✔* |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✔ |
|
HERO (2014) |
✔ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
*Does not include USB-C cable
Compatible with 5V USB Devices.
How long will the battery last before it is discharged?
It depends on many factors: the controller you are using, the camera you are using and the shooting schedule you have programmed. There are just too many variables to give an accurate answer.
In theory, the 4,000 mAH V15 battery combined with the standard GoPro 1,050 mAH battery will give you about 5 times the shooting time.
The 12,000 mAH V44 battery combined with the standard GoPro 1,050 mAH battery should give you more than 12 times the shooting time.
An analysis of the power consumption of the various GoPro cameras and an explanation of how to calculate the theoretical battery life is outlined on the GoPro Power Consumption page. Our Time Lapse Calculator page can be used to assist you in planning the interval times of your time lapse project.
How can I tell when the battery is in Always On mode?
It is easiest to determine the operating mode when the battery is disconnected and neither charging or supplying power to a device. When in Always On mode, if you double tap the power button a few times, the LED should continue to stay lit. If the LED goes dark between every other double press, you are not in Always On mode.
How can I change the operating mode?
To switch modes, hold down the power button for at least six seconds.
If you are not in the desired mode. Press the button again for at least 6 seconds to change modes.
General support can be found on our Support pages here.
Average GoPro recording times in each video setting (limited by battery capacity)
Also read the FAQ's tab for more information.
Product Code: BAT02
Sold Out
Product Code: BAT03
The V72 battery does not fit inside our Outdoor Enclosures and cannot be used with the CamDo controllers for long term time lapse. The V72 battery does not have the Always On feature that is available on our V15 and V44 battery packs. Since our controllers turn the camera off between triggers to conserve power, the Always On operating mode is required to prevent the battery from automatically turning off due to inactivity. The V72 is useful for recharging a laptop or camera batteries in the field. The V72 battery stays on only if sufficient power is being drawn.
Calculating battery life is non-trivial. It depends on the camera model, firmware version, SD card speed, lighting conditions, battery size, age of the battery, ambient temperature, and more. To help you understand the issues and to calculate estimated battery life, consult the Camera Power Consumption Study and our Time Lapse Calculator.
The V72 battery does not have the Always On feature. It cannot be used with the CamDo controllers for long term time lapse. It is useful for recharging a laptop or camera batteries in the field.
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✔* |
|
HERO5 Session |
✔* |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✔ |
|
HERO (2014) |
✔ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
*Does not include USB-C cable
Compatible with 5V, 12V, 16V and 19V Devices.
Can the V72 be used with Blink for long term time lapses?
No, the V72 battery does not have the Always On mode (available on our V15 and V44 battery packs) that is required when using our Blink controller to prevent the battery from automatically turning off due to inactivity. Since Blink turns the camera off between intervals to conserve power, the V72 will automatically shutdown after a few minutes of inactivity and require manually pressing the power button of the V72 battery to turn it back on.
How long will the battery last before it is discharged?
It depends on many factors: the controller you are using, the camera you are using and the shooting schedule you have programmed. There are just too many variables to give an accurate answer.
An analysis of the power consumption of the various GoPro cameras and an explanation of how to calculate the theoretical battery life is outlined on the GoPro Power Consumption page.
Has the V72 battery been used for long term projects?
The V72 battery stays on if sufficient power is being drawn. If the camera is powered from the V72 battery with no battery in the camera, the battery should not shut down and the camera can operate for long periods. In our tests, the HERO3+ Black operated for over 24 hours in video loop mode starting with a fully charged V72 battery.
With the WiFi turned on, even if the camera is off, sufficient power is drawn to keep the battery from shutting down. In this mode, the HERO3+ Black, with no battery in the battery compartment draws about 0.4 watts. So the camera can remain in standby mode with a WiFi connection for 150 hours.
One of our customers reported using the V72 battery with the BE-12V Battery Eliminator (discontinued) powering a HERO3 Black for a 24+ hour time lapse at one shot per 10 seconds using the GoPro Time Lapse function and no intervalometer. The camera took 11,000 photos and used 33GB of SD card space.
General support can be found on our Support pages here.
Average GoPro recording times in each video setting (limited by battery capacity)
Also read the FAQ's tab for more information.
Discontinued $220.00 USD
Product Codes: MD-003XX (X-Band)
MD-003PX (PIR)
This product is available while supplies last and has been replaced by our new Blink time lapse and motion detection controller. Motion detectors compatible with Blink are available here.
Please note that this X-Band Motion Detector (MD-003XX) is not compatible with Blink.
Motion detection can be used for security camera applications, wildlife photography, and for recording events where a person or other object, such as a car or truck, moves past the camera from time to time.
The GoPro Controller is a small high quality circuit board that plugs into the HERO Port on the back of the GoPro cameras. It is small enough to fit inside the extended back doors provided with the GoPro accessories such as the GoPro LCD BacPac or the GoPro Battery BacPac.
The CamDo Motion Detector control board is configured to trigger the camera using the output from an active doppler X-Band Microwave Motion Detector. The detector is powered by a regulated power supply on the controller board which converts the camera battery voltage to a regulated 5 volt supply.
The Motion Detector controller board can be purchased separately from our sensors for use with a different motion detector, proximity detector, or other sensing device you may already have. The board includes a 5 volt power output for use in powering accessories using the camera battery and the firmware for motion detection or triggering as described in the operating manual.
The X-Band detector board measures 1.8” x 1.6" (46mm x 41mm).
NOTE: HERO4 compatibility can only be achieved through a custom firmware modification to the camera. The firmware modification is explained in detail here.
You are strongly advised to use an SD card from the recommended list on GoPro's website. Use of cards not on the list, especially SanDisk Ultra cards, will greatly increase your chance of trouble with your setup.Capture Triggers
Programming Flexibility
External Output
No Additional Battery Required
Compatible with the GoPro camera with a HERO Port connector on the back of the camera (with the exception of the HERO3 Silver).
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔* |
|
HERO4 Silver |
✔* |
|
HERO4 Session |
✘ |
|
HERO (2014) |
✘ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✘ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
* HERO4 compatibility can only be achieved through a custom firmware modification to the camera. The firmware modification is explained in detail here.
With the current GoPro firmware, the Intervalometer can turn the HERO3 Black, HERO3+, and HERO4 cameras on, but it cannot turn them off. The camera must be programmed to turn off after taking a photo or shooting a video of the desired length using scripts which are installed on the SD card. This allows for considerable flexibility in deciding what the camera will do when triggered by the Intervalometer. Sample HERO3+ and HERO3 Black scripts can be seen here. HERO4 scripts are structured differently, and their feature set can be seen here.
Scripts are not required for HERO2 or HERO3 White cameras.
Learn how to use your Motion Detector Controller and get all the info you'll need here.
Frequently Asked QuestionsAre the motion detectors compatible with the new HERO4 camera?
The motion detector is compatible with all GoPro HERO cameras, except the HERO3 Silver and the entry level grey HERO cameras. The HERO4 solution requires the use of GoPro’s most recent firmware in addition to a firmware patch provided by CamDo, which will be emailed to you after you purchase your product.
If you do not require a product configuration immediately, you may also be interested to know that we’re in the process of creating a great product that will replace three of our most powerful products: Programmable Scheduler, Time Lapse Intervalometer and Motion Detector. This product will have a WIFI chip that enables the user to control the camera through a web based UI. We hope to have this available this winter.
What is the difference between the PIR and X-Band Motion Sensor?
The PIR Sensor detects movement by registering the change in infrared emissions from a warm body by comparing multiple panels in its view. Therefore it detects warm objects moving across the sensor, side to side or up and down. The X-Band sensor uses doppler detection of microwaves bounced off the object and is triggered by motion towards or away from the sensor.
Infrared can pass through some thin transparent or translucent plastics, but in general, not through glass. Microwaves pass through opaque plastics and glass, but not metal. The moving object does not need to be warm to trigger the sensor.
Can I use more than one sensor?
Yes. Multiple sensors can be connected in a logical OR so that any one sensor will trigger the camera. This means that multiple sensors of different types, including sensors from other suppliers in many cases, can be placed in different locations in order to trigger the camera more reliably or in advance of an animal moving into a scene.
Does the controller board fit inside the waterproof case?
The board does not fit in the standard case. The board fits in the extended backdoors provided with the GoPro accessories such as the GoPro LCD Bacpac or the GoPro Battery Bacpac. A small hole can be drilled into the housing to allow the sensor’s wires to pass through the housing.
A simple means of securing the camera with the controller board in the standard case for use indoors or in good weather, is to use an O-ring or a rubber band to hold the camera in the case with no backdoor. Pictured is an AS568-134 which fits nicely.
Outdoor Weather Resistant Enclosure
CamDo now offers an Outdoor Weather Resistant Enclosure designed to house the Motion Detector and other CamDo controllers along with space for a high capacity battery.
The X-Band detector fits inside the weather resistant case and does not require any hole in the case for installation.
A case for the PIR detector will have an additional opening for the PIR detector lens.
How can I setup the motion detector to only trigger during the day?
It is possible to use a simple photocell to prevent triggering at night. If you have a slight knowledge of soldering, you will probably be able to follow the instructions in the Application Notes.
I am a hacker. Can I use the cable on the board to trigger the camera using other devices?
Yes! If you have a little knowledge of electronics, you can use the controller board to trigger the camera. The interface is documented in the CamDo Controller Application Notes for Advanced Users. It is actually quite easy to connect external triggers such as motion detectors, intervalometers , security systems, or to configure the camera to start automatically whenever the car ignition is turned on, for example.
I am a not a hacker. I have an idea for a project for our organization. Can you help?
Yes. The controller board was originally designed to handle custom projects we built for scientists and professional photographers. It is very flexible and can be reprogrammed to respond to different kinds of control inputs. It also has an opto-isolated output which can be used to control lighting, or give different types of feedback. Contact us for a quote for your application.
I know how to write code for the MSP430 processor. Can I reprogram the chip with my own firmware?
Yes. The SBW interface is brought to the edge of the board, so you can even use the Texas Instruments Launchpad ($4.30) to program the device. There is a tutorial: Use your launchpad as a programmer. Let us know if you come up with something really brilliant!
$25.00 USD
Product Code: IHB01
The GoPro 30 Pin HERO Port connectors fit all GoPro models with a HERO Port on the back of the camera. These connectors are ideal for the hobbyists who wish to build their own cables or experiment with the GoPro camera's HERO Port connection.Solder the pins by hand
Perfect for prototyping
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✘ |
|
HERO (2014) |
✘ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
Compatible with all GoPro cameras with the HERO Port at the back of the camera.
It looks just like my iPhone charger cable. Can I just use the one I have?
No! The iPhone/iPod cable has a very similar connector to the GoPro Port connector, but the connections are different. You will almost certainly damage the camera if you try to charge the camera with an iPhone cable.
iPhone connectors are actually a slightly different size from the GoPro connectors. Some knockoff connectors will fit the camera, but they may distort the GoPro’s HERO Port if forced.
Will the connectors fit inside the GoPro waterproof back doors?
Low profile design fits easily in any of the extended skeleton backdoors provided with the GoPro LCD Bacpac or the GoPro Battery Bacpac. accessories. The connector is narrow enough to fit inside the back door and the cable fits easily through the slot at the bottom. Alternatively, a hole can be cut in the back of the standard skeleton backdoor.
Where can I find documentation on the GoPro HERO Port interface?
The GoPro User Forum is the best place to find unofficial documentation discovered by users who were not afraid to take their cameras apart and poke around.
How are the pins numbered?
$39.00 USD
The LED Wired Remote cable can be used with the BlinkX and Blink to trigger the controller's WiFi signal from a distance. The remote's cable is 3ft long and we offer 2.5mm Extension Cables if a longer distance trigger is needed.
The LED of the remote will turn on to provide a visual indication when the GoPro camera has been turned on.
The LED Wired Remote is used with the CamDo Bullet for the GoPro HERO3+ and HERO4 cameras to allow you to control the GoPro camera's power and shutter functions with the push of a button. The Wired Remote can be used to control a single camera through the Bullet's input port. The output port from the Bullet can be daisy-chained to another Bullet’s input to simultaneously control multiple cameras with a button press from a single Wired Remote.
When used with the Bullet, the LED indicator on the remote will mimic the red LED on the front of the GoPro camera: blink once to indicate taking a picture, and blink continuously to indicate that the camera is recording, etc.
THE LED WIRED REMOTE IS PURCHASED SEPARATELY FROM THE BULLET. Be sure to purchase a LED Wired Remote for each set of Bullets.
Remote Control of Multiple GoPros
Through the use of a set of Bullets, trigger as many GoPro cameras as you want with a push of a button of the Wired Remote.
Low Power Consumption for Extended Use
When used with Bullet(s), the LED Wired Remote extends your camera’s battery life by allowing you to control the power and shutter functions of your GoPro cameras without the considerable power required for WiFi control.
Product Code: AWR01
$495.00 USD
File management for dozens of SD cards simultaneously has never been easier with the CamDo Grab software for use with the PowerPad.
The PowerPad Multi Camera Charge and Sync Station can supply each USB port with 2.1 amps of power at 5.2 volts DC, sufficient for rapid battery charging or for operating tablets as well as GoPro cameras. The PowerPad15S can charge and download files from up to 15 cameras, while the PowerPad8S handles up to 8 cameras. The PowerPad is capable of recognizing any USB chargeable device and automatically configuring itself to emulate the appropriate charger for maximum charging efficiency on each USB port.
When the PowerPad is connected to a host computer, each camera can be switched from “data-connected” (for charging and file management) to “data-disconnected” (for only charging) under the control of the host computer. This allows the use of multiple cameras without the need to plug and unplug cables or remove the SD cards from the cameras. Standard USB cables can be used to connect the cameras to the PowerPad unit.
In the PowerPad's "data-connected" computer connected sync mode, the host computer sees each camera’s SD card and mounts them as individual disks. Files can be downloaded from the SD cards at up to 480 Mb per second. The cards can be erased and control scripts can be uploaded from the host computer. (HERO3 and HERO3+ use SOBM scripts, HERO4 use CSI scripts)
*While the PowerPad can be used with all operating systems and cameras, currently, the CamDo Grab Software is only compatible with Windows Software and HERO4 cameras.
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✔* |
|
HERO5 Session |
✔* |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✔* |
|
HERO (2014) |
✔* |
|
HERO3+ Black |
✔* |
|
HERO3+ Silver |
✔* |
|
HERO3 Black |
✔* |
|
HERO3 Silver |
✔* |
|
HERO3 White |
✔* |
|
HERO2 |
✔* |
|
HERO |
✔* |
Is the PowerPad compatible with Macintosh, Linux, Windows?
The PowerPad is compatible with all operating systems, including Windows, Mac and Linux. Any computer which is a USB compatible host can be used to control the PowerPad. However, the CamDo Grab software can only be used on a Windows operating system
What port do I use to connect the PowerPad to my computer?
The USB port labeled “Host Port” is used to connect the PowerPad to your computer or power supply. 
I need more than 15 cameras. Is there a bigger unit available?
Each PowerPad15S unit can charge and connect to 15 cameras. Multiple PowerPads can be plugged into separate USB ports on the computer or a USB hub. A PowerPad cannot be plugged into one of the ports of another PowerPad.
Will the system be compatible with future versions of the firmware/camera?
The firmware in the PowerPad is upgradeable. If there are changes in camera firmware that necessitates it, new firmware can be downloaded and installed.
The PowerPad comes with a 12 month manufacturer's warranty.
General support can be found on our Support pages here.
If you have a problem with your PowerPad or need more detailed information, you can ask the folks at Cambrionix. They will be most helpful. Cambrionix Troubleshooting.
Product Codes: PowerPad15S - PPP01
PowerPad8 - PPP02
Discontinued $189.00 USD
Product Code: PS-004
THIS PRODUCT IS DISCONTINUED. Purchase the all-new Blink, which has the same features and more!
The CamDo GoPro Programmable Scheduler combines the functions of the CamDo Time Lapse Intervalometer with a programmable timer capable of storing 17 separate programs for shooting long term time lapse sequences or video at specific times on specific days.
For time lapse, the CamDo Scheduler Control is designed to turn the GoPro camera on and off to maximize the battery life. In most cases, the camera will take about 2,000 images on a single battery charge (750 on the Hero3 Black). These images can be spread over hours, days or even weeks without recharging the battery.
The ability to schedule the beginning and end times of the time lapse function lets the photographer program time lapse sequences to be shot during certain hours of the day, every day or every business day. Or, it can be used to schedule the start of a time lapse sequence up to one week ahead.
Examples:
For video, the scheduler can be programmed to shoot short video clips at multiple desired times, or to turn the GoPro camera on and shoot for several hours starting at a predetermined time after a delay of up to one week.
Examples:
NOTE: HERO4 compatibility can only be achieved through a custom firmware modification to the camera. The firmware modification is explained in detail here.
You are strongly advised to use an SD card from the recommended list on GoPro's website. Use of cards not on the list, especially SanDisk Ultra cards, will greatly increase your chance of trouble with your setup.Intervalometer Features included on Programmable Scheduler
No Additional Battery Required
Compatible with the GoPro camera with a HERO Port connector on the back of the camera (with the exception of the HERO3 Silver).
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔* |
|
HERO4 Silver |
✔* |
|
HERO4 Session |
✘ |
|
HERO (2014) |
✘ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✘ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
* HERO4 compatibility can only be achieved through a custom firmware modification to the camera. The firmware modification is explained in detail here.
With the current GoPro firmware, the Intervalometer can turn the HERO3 Black, HERO3+, and HERO4 cameras on, but it cannot turn them off. The camera must be programmed to turn off after taking a photo or shooting a video of the desired length using scripts which are installed on the SD card. This allows for considerable flexibility in deciding what the camera will do when triggered by the Intervalometer. Sample HERO3+ and HERO3 Black scripts can be seen here. HERO4 scripts are structured differently, and their feature set can be seen here.
Scripts are not required for HERO2 or HERO3 White cameras.
Learn how to use your Programmable Scheduler and get all the info you'll need here. View Product Documentation >
Setting Up Your Programmable Scheduler:
Is the Scheduler Waterproof?
The Scheduler itself is not waterproof and does not fit inside the GoPro waterproof housings. It needs to be sheltered from the elements. The Scheduler can be attached to the camera when it is in a GoPro housing with the back removed.
CamDo offers an Outdoor Weather Resistant Enclosure designed to house the Programmable Scheduler and other CamDo controllers along with space for a high capacity battery.
How long will the battery last if I shoot some number of photos per hour?
Calculating battery life is non-trivial. It depends on the camera model, firmware version, SD card speed, lighting conditions, battery size, age of the battery, ambient temperature, and more. To help you understand the issues and to calculate estimated battery life, consult the Camera Power Consumption Study and our Time Lapse Calculator.
Does the Scheduler work with your Battery Eliminators?
We recommend using the Scheduler with a HERO3/3+ Battery Eliminator. There is a slot in the back of the scheduler for the Battery Eliminator cable to pass through.
Using the Battery Eliminator reduces heat from the camera battery and charging circuit. A Battery Eliminator also bypasses the problems that some users have had with the GoPro charging logic when charging from the camera’s USB port causing the camera to freeze and require a reset.
Our HERO4 Battery Eliminator uses the same HERO Port as the Scheduler. Therefore the two items cannot be used together. Charging a HERO4 would need to be done using the camera’s mini-USB port.
Can a solar panel be used to extend the operating time?
The shooting time can be extended using a USB battery pack or AC charger attached to the camera. A solar powered battery pack can be used to shoot until the SD card is full.
CamDo offers a complete solar system including the solar panel, a 4000 mAH battery, and a weather resistant enclosure.
For information about the camera power consumption, battery requirements, and solar energy considerations, consult our Camera Power Consumption Study and our Time Lapse Calculator.
Can I download images via USB while using the Scheduler?
Yes, this works very well with the Hero3 Black & White cameras. A long USB cable can be permanently connected to the camera. Plug the USB cable into a computer. The images can now be moved from the SD card to your hard drive. When you unplug the USB cable from the computer, the camera will turn off. The scheduler will resume shooting with the next image. There is no need to touch the camera. The USB cable can be plugged into a charger or large battery pack while shooting for longer battery life.
We stock a 10 foot USB cable that has been tested to work for charging and downloading.
What do our customers use our Programmable Scheduler for?
It delights us to hear from happy customers who have used the Programmable Scheduler to take photos and videos in interesting ways.
Sometimes it is not possible to be there when you want to shoot a video. Matt Harman of Shorealone Films set up the Programmable Scheduler to shoot this video.
“I used the scheduler in 0110 mode to record the lift off of the Delta 4 Heavy. We set up the day before launch and I had it programmed to turn on 2 mins before the launch window opens, just to be safe in case of any problems, and then at 12:00 when the window closed to power off and stop recording. As you can see from the video it's not safe to be standing anywhere near that rocket when it goes off. I'm just happy it wasn't incinerated like the hillside behind it. The CamDo Scheduler allows me to record impossible video from anywhere right on time.”
I will be buying more...thank you for all your programing skills..... -MH
Lance Hastie in Christchurch New Zealand used the Programmable Scheduler to film the construction of an ice rink in a parking lot for the school holidays.
“I used the Programmable Scheduler set for 5 minute intervals to film the time lapse sequences in this clip. It was remote powered via the USB port to keep the battery charged from a 12V SLA feeding a 5V regulator. One charged SLA lasts 10 days safely operating 7:30am to 6pm, at 5min photo image cycles. All worked perfectly.” -LH
Jérôme Balleydier of Aérographe in Réunion Island created a 3 month time lapse of the construction of a solar energy generation site with the CamDo Solar powered system.
Zirriborro TV in Bilbao, Spain, have been using two PS-003 Programmable Schedulers to document the transformation of the Tabakalerako Tobacco building into a culture center.
Marco Zecchin Photographic Art in California, uses a PS-003 with a Hero3+ to shoot time lapse videos of construction projects like this one.
$56.00 USD
Product Code: ASD03
The SanDisk Extreme 64GB microSDXC Memory Card from is A2 and U3 rated to provide a minimum write transfer rate above 30MB/s (U3 rated SD cards are required for use with GoPro cameras). This SD card is supplied with a "full sized SD" card adapter for high-speed file transfer to your computer via an SD card port.
Discontinued $199.00 USD
Product Code: CTL01 (Naked)
TL-004A (Acrylic)
We now have limited stock of the Naked Time Lapse Intervalometer (TL-004N) which is suitable for older GoPro cameras. If you are using a HERO3+ or HERO4 cameras, we suggest purchasing the all-new Blink, which has the same features but has more programming flexibility and is configurable using a simple Web Interface and more!
The Intervalometer is a small high quality circuit board that plugs into the HERO Port on the back of the GoPro camera. The Intervalometer is small enough to fit inside the GoPro HERO3 Frame Mount or the extended back doors provided with the GoPro accessories such as the GoPro LCD BacPac or the GoPro Battery BacPac.
In the time lapse operating mode, the Intervalometer can be programmed to turn the camera on at a regularly spaced interval so that the GoPro can capture an image or video before turning the camera off to maximize the battery life. In most cases, the camera will take about 700 images on a single battery charge (2,000 on the HERO2). These images can be spread over hours, days or even weeks without recharging the battery.
The Intervalometer has multiple operating settings and input/output pins that allow for the board to be applicable to various custom solutions. Read more about the Intervalometer's other features for advanced applications here.
Note that the Intervalometer is only capable of turning on the HERO3 Black and newer GoPro cameras but not off. Functionality on these cameras is achieved through the use of our scripts saved to the SD card. The scripts are normally used to take a picture or record for a set amount of time before turning the camera off so that it can be re-triggered by the controller. (Blink can control the power, mode, and shutter functions of the HERO3+ and HERO4 cameras without scripts)
Compatible with the GoPro camera with a HERO Port connector on the back of the camera (with the exception of the HERO3 Silver).
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔* |
|
HERO4 Silver |
✔* |
|
HERO4 Session |
✘ |
|
HERO (2014) |
✘ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✘ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
* HERO4 compatibility can only be achieved through a custom firmware modification to the camera. The firmware modification is explained in detail here.
With the current GoPro firmware, the Intervalometer can turn the HERO3 Black, HERO3+, and HERO4 cameras on, but it cannot turn them off. The camera must be programmed to turn off after taking a photo or shooting a video of the desired length using scripts which are installed on the SD card. This allows for considerable flexibility in deciding what the camera will do when triggered by the Intervalometer. Sample HERO3+ and HERO3 Black scripts can be seen here. HERO4 scripts are structured differently, and their feature set can be seen here.
Scripts are not required for HERO2 or HERO3 White cameras.
How long will the battery last if I shoot some number of photos per hour?
Calculating battery life is non-trivial. It depends on the camera model, firmware version, SD card speed, lighting conditions, battery size, age of the battery, ambient temperature, and more. To help you understand the issues and to calculate estimated battery life, consult the Camera Power Consumption Study and our Time Lapse Calculator.
I want to shoot a 4 minute video of a 4 month construction job. How do I do that?
You want each month to be one minute of video. That is about 2 seconds per day, or 60 frames at 30fps. Shooting 24 hours a day, that is one shot every 24 minutes, or about one shot every 10 minutes if you only care about the daytime (acquiring shots for daytime only can be done using our Blink Controller or by removing nighttime shots during post-production). Our Time Lapse Calculator can be used to estimate the SD card and power requirements based on your setup.
In practice, things go wrong. The camera can stop working. The battery might not have been fully charged. The SD card may have a flaw. A bird dropping might block the lens. We never recommend leaving the camera unchecked for more than a few days. Always assume that what can go wrong, will go wrong. Use two cameras to get different angles and to provide backup if something happens to one camera.
I only want to shoot from 9 to 5, Monday through Friday. How can I best do that?
Our Blink product is designed for that purpose. It is easy to set up to capture an image or video at certain times or to enable time lapse captures on a specific schedule.
Does the Intervalometer retain its settings when I remove it from the camera?
Yes, the settings are stored in flash memory and will be retained until you program different settings or do a factory reset.
Does the Intervalometer board fit inside the waterproof case?
The Intervalometer does not fit in the housing shipped with the camera. It fits in the extended backdoors provided with the GoPro accessories such as the GoPro LCD Bacpac or the GoPro Battery BacPac.
The TL Controller fits in the GoPro HERO3 Frame Mount, which comes with 2 frames, one for the camera alone, and one which holds the camera and BacPac accessories, such as the Battery BacPac and the CamDo Time Lapse Intervalometer. Be careful, if buying on eBay, where you might not get both together.
Another simple way to secure the camera and Controller board in the standard case for use indoors or in good weather, is to use an O-ring or a rubber band to hold the camera in the case with no backdoor. Pictured is an AS568-134 O-ring which fits nicely.
Do you have a weather resistant enclosure to also house battery packs?
CamDo offers an Outdoor Weather Resistant Enclosure designed to house the HERO3, HERO3+ or HERO4 cameras with the Time Lapse Intervalometer or other CamDo controllers along with space for a high capacity battery packs.
Can a solar panel or AC power source be used to extend the operating time?
The cameras can be powered by external batteries charged from a solar panel or another suitable power source.
The CamDo Solar System includes a solar panel, high powered lithium battery, and a weather resistant enclosure. Our Time Lapse Calculator can be used to determine if a 6Watt or 9Watt solar panel would theoretically be able to keep your system running continuously throughout your project.
Does the Intervalometer work with your Battery Eliminators?
The Intervalometer utilizes the HERO Port on the back of the camera so it cannot be used at the same time as the HERO Port Battery Eliminator.
When using the Intervalometer with HERO3 or HERO3+ camera, we strongly recommend using an H3 Battery Eliminator. There is a slot in the back of the Acrylic Intervalometer for the H3 Battery Eliminator cable to pass through.
Using the Battery Eliminator reduces heat from the camera battery and charging circuit. A Battery Eliminator also bypasses the problems that some users have had with the GoPro charging logic when charging from the camera’s USB port causing the camera to freeze and require a hard reset.
I am a hacker. Can I use the extra connections on the board to trigger the camera?
Yes! If you have a little knowledge of electronics, you can use the Intervalometer Naked PC board to trigger the camera. The interface is documented in the CamDo Intervalometer Application Notes for Advanced Users. It is actually quite easy to connect external triggers such as mobile phones, Android devices, computers, motion detectors, intervalometers, programmable timers, security systems, accelerometers that detect motion, or to configure the camera to start automatically whenever the car ignition is turned on.
I am a not a hacker. I have an idea for a project for our organization. Can you help?
Yes. The Intervalometer board was originally designed to handle custom projects we built for scientists and professional photographers. It is very flexible and can be reprogrammed to respond to different kinds of control inputs. It also has an optically isolated output which can be used to control lighting, or give different types of feedback. Contact us for a quote for your application. Our rates for custom firmware are very reasonable.
I know how to write code for the MSP430 processor. Can I reprogram the chip with my own firmware?
Yes. The SBW interface is brought to the edge of the board, so you can use the Texas Instruments Launchpad ($4.30) to program the device. There is a tutorial: Use your launchpad as a programmer. Let us know if you come up with something really brilliant!
What do our customers use our Intervalometer for?
It delights us to hear from happy customers who have used the Intervalometer to take photos and videos in interesting ways. We have been even more delighted to see customers returning to order multiple units on their second order.
Tell us what you used your Time Lapse Intervalometer for!
Canterbury Earthquake Recovery (Lance Hastie)
General support can be found on our Support pages here.
Average GoPro recording times in each video setting
Also read the FAQ's tab for more information.
$12.00 USD
Product Code: USB-3FT - LUS01
USB-10FT - LUS02
This cable features a standard USB A male connector on one end and a 5-pin mini B connector on the other. It uses 24AWG conductors for the power lines and 28AWG conductors for the data lines, for improved current carrying capacity. The cable is shielded using braid and foil shields and it includes a single ferrite core, which helps filter out electromagnetic and radio frequency interference (EMI and RFI). The connectors are gold plated for smooth, corrosion free connections.
High Speed Charge and Download
Noise resistant
Durable construction
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✔ |
|
HERO (2014) |
✔ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔ |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
What is the difference between 28/24AWG and regular 28AWG USB cables?
The 28 AWG data conductors are standard for download data at USB 2.0 speeds. The power conducting wires are built to a thicker 24 AWG. The increase in thickness of the power wiring allows the cable to carry more power and charge devices at a faster rate.
Discontinued $99.00 USD
Product Code: (Acrylic + Cable) - CVA01
The GoPro Video Monitor Adapter plugs into the connector at the back of all GoPro HD HERO, HERO2, HERO3, HERO3+, and HERO4 cameras. The adapter provides 480i SD composite video compatible with all LCD and CRT monitors and video transmitters and receivers.
The CamDo video adapter for the GoPro camera converts the signal normally displayed on the GoPro LCD BacPac to a composite video signal which can be displayed on any monitor with a composite video input.
With a large display, separate from the camera, you can easily frame your image and navigate the GoPro menus to set up for a shoot.
 |
The Naked PCB version is fully assembled, programmed, and ready to use. Just connect your own video cable and plug the board into the camera. |
 |
The Naked PCB + Cable version includes a short coax cable with a male RCA plug compatible with most consumer video devices. |
 |
The Acrylic + Cable version is enclosed in a custom made acrylic enclosure which fits comfortably in the GoPro extended backpacs and includes the cable with RCA connector. |
Compatible with all video transmitters.
The composite video signal can also be transmitted by any video transmitter to a compatible receiver for wireless remote viewing. Tiny video transmitters for R/C planes and quadcopters can be used in real time with no delay for FPV flying or just framing the image being captured by the GoPro camera in high definition.
Video Signal Transmission
Remote Trigger (available with PCB version)
External Output (available with PCB version)
No Additional Battery Required
|
Camera |
Compatibility ( Y / N ) |
|
HERO5 |
✘ |
|
HERO5 Session |
✘ |
|
HERO4 Black |
✔ |
|
HERO4 Silver |
✔ |
|
HERO4 Session |
✘ |
|
HERO (2014) |
✘ |
|
HERO3+ Black |
✔ |
|
HERO3+ Silver |
✔ |
|
HERO3 Black |
✔ |
|
HERO3 Silver |
✔* |
|
HERO3 White |
✔ |
|
HERO2 |
✔ |
|
HERO |
✔ |
Compatible with the GoPro camera with a HERO Port connector on the back of the camera.
* Trigger function not available on the HERO3 Silver.
Information about how to use the PCB Video Monitor Adapter’s trigger and LED pins can be found here.
View Application Notes for Advanced Users >
Frequently Asked QuestionsWhich models of GoPro cameras are compatible with the Video Monitor Cable?
All models of GoPro cameras equipped with a HERO Port connector on the back are compatible with the Cam-Do Video Monitor Cable. The original HERO 980 is not compatible. All other cameras including the HERO3+ and HERO4 models are compatible.
Does the adapter fit in the waterproof back?
The adapter fits inside the extended BacPacs provided by GoPro with the LCD display, battery BacPac and WiFi BacPac. The cable fits through the slot in the BacPack.
Can the adapter be used underwater?
A waterproof version for underwater use with a cable leading to the surface is currently in development. We have tested it to 30 feet with a 100 foot cable and will be doing more testing before offering this new product. It will probably come with a cable, a video output plug, and optionally the possibility of powering the camera from a 12 volt source and triggering the start and stop with a remote button. If such a product is of interest, please contact us to participate in the final design decisions by telling us how it would be useful for you.
Can the camera be powered by the adapter?
Charging via the video board works with HD HERO and HERO2 cameras. The adapter has connections for 5 volt USB power to keep the camera battery charged for long usage or to power the camera without the battery when trying to minimize weight. External power via the Adapter does not work with the HERO3 or HERO4 camera. For HERO3/3+, Battery Eliminators should be used. For HERO4, the USB power input should be used.
I bought the bare board, where do I connect the video out?
VIDEO For video out, connect a cable to the contacts at the lower right. No other connections or power supply are required.
LED An LED can be connected for visual indication of when the camera is on, or for telemetry in FPV systems, or feedback in automated control systems.
Trigger Closing a contact across the trigger connections briefly will turn on the camera. One button mode can be used to start filming. Super One Button Mode scripts can be used with HERO3 and HERO3+ cameras. CSI scripts are used for HERO4 cameras.
5V DC can be applied to power the GoPro camera.
If your board is a previous revision click here to see the connection diagram.
Free
Product Code: SWI01
We're always trying to improve our products. Please click here to answer a few questions about our WIGO application.
WiGo is a Windows application designed to communicate with GoPro WiFi enabled cameras that can be used to change the camera settings, preview the image, and download photos and videos directly to your PC from the SD card.
Shortly after the iPhone application was released by GoPro, a number of enterprising individuals began to catalog the WiFi commands sent from that app to the GoPro Wifi BacPac. They were generous enough to share their observations on the GoPro User Forum. In particular, dough29 contributed enormously to the task of documenting the List of GoPro Wifi BacPac Commands and has built RemoteGo, an Android app to control the camera. This software builds on their work. Thank you.
WiGo does not require any installation. Download the WiGo.exe file (which will be delivered to you via email) to the folder you wish to use and run it. Your browser and Windows will warn you that this is unsafe. They are right. It is always risky to download an executable file from an unknown source. Never install WiGo or any other program if you are unsure of the source. If you download from cam-do.com, WiGo.exe is coming directly from the author. It does not contain malware of any kind. Never download WiGo.exe from any other site.
Disclaimer:
This is beta testing software. Use at your own risk. This software may damage your camera. The responsibility is entirely with the user. The author accepts no responsibility for any damage that may be caused by using this software.
Can WiGo be set up to automatically take pictures and upload them to a web site for remote viewing?
The free version does not include those features. We are working on a WiGo Professional version that will incorporate many of the extra features that have been requested by our corporate clients. The ability to control multiple cameras with one WiFi adapter and upload the captured photos to a web site on a regular schedule is the most important feature of WiGo Pro. If this is a feature you would like to make use of, please contact us for further details or to influence our design decisions.
What versions of Windows will WiGo run on?
It has been tested on Windows 10, Windows 8, Windows 7 and Windows XP. There is no reason it shouldn't run on almost all Windows versions released in this century. SSID display and automated camera selection are only available in Windows 7 and 8. Users report that it works with the Windows 8 Microsoft Surface Pro Tablet.
Will it work with my camera?
It works with all 3 versions of the HERO3 Cameras and the HERO2 with the WiFi BacPac accessory. There are some features that only work with particular cameras because of the features GoPro has included or the way they have configured their firmware.
HERO3+ includes some new settings and status feedback that were not available in the previous cameras. WiGo works with the HERO3+, but not all settings. HERO4 and HERO5 is not supported.What are the users saying about WiGo?
Feedback has been almost 100% positive. Quite a few users have been happy enough to donate. For example, read these unsolicited emails:
I'm just writing to thank you so so much for the WiGo... i`ve been for about a week or so trying to get the GoPro App through an android emulator for PC and was just about to lose my goddamn mind when I stumbled upon your website, and your wonderful wonderful software. Congratulations on developing this way before GoPro did, or should have done (still dont know why) but the program works amazingly. I don't know if you updated the software since the last time you posted any comments, but I have a HERO3 WHITE ED. and EVERYTHING worked perfectly !!!!! The Previews, the functions, the mode selection, the options selection....everything commanded through the software, the only issue that I believe is normal is the 2 or 3 second delay on the preview image !! but that is expected...and being what it is...even welcome...lol !!!!
- Leonardo in Sao Paulo
Your program fixed my HERO3 Silver blue light problem!!!
Ever since I did the newest firmware update on my HERO3 Silver the blue WiFi lights don't work anymore. This started to cause a problem because you would never really know when the WiFi antenna was on or off. The WiFi button is very easy to activate by accident. It would turn on with out me knowing, rendering the camera battery dead when you wanted to use it. When the camera is off the only way to know the WiFi antenna is on was the blue light blinking.
I found your program online wanting to connect my GoPro to my laptop via WiFi for streaming or just something neat to have.
First of all, on my HERO3 Silver everything works perfectly!!!
I was messing around with the settings for the LEDs in WiGo. Turned the LED setting off then on and now the blue lights work again!!!! Don't know how it fixed it, but it did and has worked ever since.
Now I know when the antenna is really on or off again.
Thank you thank you thank you for such an awesome program. Your time is much appreciated.
I will certainly mention this awesome program and website to my fellow users and also suggest a donation to your efforts.
Thanks again!
- Josh
Tips & Troubleshooting
Streaming video is delayed or cuts off after a few seconds.
The delay is normal and is part of the GoPro implementation.
Some users have reported the streaming working without problems. Others seem to have it stop intermittently. Make sure the firmware in the camera is up-to-date and installed properly. Sometimes a manual install fixes problems after GoPro's automated install has appeared to work. Make sure you are using the latest version of VLC. Restart your computer after updating VLC. WiGo does no more than pass the address of the camera's streaming feed to VLC.
One VLC setting that improves streaming is under VLC - Tools - Preferences - Input & Codecs - Default Caching Policy - select Lowest Latency. There are a lot of settings which can be optimized and perhaps a VLC guru can tell us the best combination.
I see the SD Card on the HERO3 Black but there are no image files.
The latest firmware from GoPro for the HERO3 Black disabled the image file display on the camera's web server. It is possible to run a SOBM script on your SD card which will modify the firmware in the camera to show the files.
Is it possible to capture the streaming video or forward it via the internet?
Yes, it is. It can be done using the features of VLC or with utilities such as FFmpeg and FFplay. TechAnswerGuy has blogged about the process and gmore70 has created a tutorial video showing how to stream GoPro video on YouTube and UStream.
How can I extend the range from my camera to my computer?
There are several ways to do this. One is to use a range extender, which repeats signals from the computer to the camera and vice versa.
Can I control multiple cameras with one computer?
There are several ways to do this. WiGo Pro can access multiple cameras and upload photos using FTP with a single WiFi adapter by accessing them sequentially or control multiple cameras connected to separate WiFi adapters by changing the camera IP address.
Known Bugs
The video mode settings are incomplete. Some video mode settings work on some cameras, but the complete set of mode values for all of the cameras has not been implemented at this time. Some mode settings may be incorrect on some camera models and work correctly on others.
© 2018 CamDo Solutions. | SALES: +1 650 353 4568 sales@cam-do.com | support@cam-do.com
