180224
Dash - GoPro Dashcam Controller
Sold Out
Use your existing GoPro as a Dashcam!
Automatically turn on the GoPro camera and start recording when power is applied to Dash. If Dash is attached to your vehicle's accessory jack, when you start/stop your engine, Dash can automatically turn on/off the GoPro camera.
-
'Dash' from CamDo converts your GoPro to a dashcam. Check out the CamDo Dashcam pack which provides you with everything to get started.
Capture exciting footage from your motorbike, race car, plane or helicopter or simply capture a family road trip or bike ride. Plus have the peace of mind if something goes wrong, you will have a record.
The miniUSB trigger input on Dash will work on any 5V power source so it can run using your vehicle's USB accessory jack, or an alternate custom trigger system of your own design. Dash uses a power regulator so the same 5V trigger signal can be used to provide power to the GoPro camera. Note: Dash is only designed for a 5V power input. Attempting to connect to a voltage greater than 5V may result in damage to Dash and/or the GoPro camera.
Dash can use any of the GoPro camera's video modes and can be configured to 8 different operating modes for flexibility. When power is applied to the trigger input, Dash can either start recording immediately, or just turn the camera on which can be useful if only using the GoPro's miniHDMI output or running scripts saved to the SD card. When power is removed, Dash can either end the recording immediately and turn off the camera, continue recording for 1 or 10 minutes before ending the recording and turning off the camera, or ignore the removal of the trigger signal and continue to stay powered on.
settingsEasy & flexible setup
- Intuitive - just plug in and get started
- Starts automatically, stops automatically
- 8 different modes for flexibility(see Support Tab)
camera_enhanceImage Quality
- GoPro 4K Image quality
- Adjustable standard and wide angle capture
- Compatible with all GoPro video modes including - record video, looping video, video & photo or video time lapse.
placeTrigger HiLight Tag
- Use the wired remote to HiLight Tag footage (HERO4 only)
extensionFlexible mounting
- Choose mount to suit your application/depth
- Cars - windscreen or dash mount
- Motorbikes
- Helicopters
- Infinite viewing / mounting angles
- See mounting options on our Dashcam pack page
-
Dash will fit inside the extended backdoors included in the GoPro Backdoor Kit that are designed to fit GoPro BacPac accessories. We recommend using the frame mount inside a vehicle.
Camera
Compatibility ( Y / N )
HERO5
✘
HERO5 Session
✘
HERO4 Black
✔
HERO4 Silver
✔
HERO4 Session
✘
HERO (2014)
✘
HERO3+ Black
✔
HERO3+ Silver
✘
HERO3 Black
✘
HERO3 Silver
✘
HERO3 White
✘
HERO2
✘
HERO
✘
Compatible with 5V USB Devices.
-
Frequently Asked Questions
Which GoPro cameras is Dash compatible with?
Please see the Compatibility tab.
My race car vibrates a lot. How do I keep secure the USB cable in Dash or the camera?
We recommend placing a loop in the USB cable and a cable tie to provide a level of security and to reduce the vibration. We also recommend mounting to the windshield where practicable which has less vibration than the dashboard.
How do I know what mode I am in?
When you plug Dash in, the LED on the back will flash the same number of times as the set mode. Eg if you are in mode 3, the LED will flash 3 times. If you are in mode 1, the LED will flash once.
Does powering Dash charge the GoPro battery?
No. While the GoPro camera can be powered through Dash, Dash does not charge the GoPro battery which makes the camera more reliable when recording for long periods by removing the heat generated by the GoPro battery charging circuit.
Do I need the internal camera battery?
Yes, the internal battery must be present to allow time for the GoPro to save the file and ensure your file is not corrupted due to the sudden loss of power. To keep your GoPro charged, we recommend also plugging power into the side of the camera via the mini USB port. The USB charger CamDo offers has 2 x USB output ports so that you can charge the camera at the same time.
Does Dash support scripting?
Yes! Using modes 5, 6, 7, or 8, the camera will only turn on, it will not automatically start recording. You are then in complete control using scripts. CamDo offers custom firmware to enable scripting on the HERO4 camera - check it out here.
How does Looping Video work with the GoPro camera?
The video looping feature of the GoPro cameras allows you to shoot 5 minutes to 2 hours of video in a continuous loop. When the programmed time is up, the camera will erase the first segment of the video and begin recording a new segment. We recommend using the 2hr setting as GoPro chaptering on the MAX setting is not ideal (see below). The video is saved in segments which can be combined using GoPro’s Cineform Studio. Segment length depends on the total time selected.
Check out our detailed blog post here about the best GoPro settings/options for use as a Dashcam.
-
General support can be found on our Support pages here.
Average GoPro recording times in each video setting (limited by SD card capacity)
Also read the FAQ's tab for more information.
Dash Modes
To enter programming mode, insert the wired remote into the “Config/Highlight” port and hold the button down while plugging Dash into the camera. The LED will periodically flash to indicate what mode it is currently set to. Each button press on the wired remote will to cycle to the next operating mode. Unplug Dash or remove all power to exit programming mode.
Mode
Camera Action / Operation
USB power received
USB power removed
1
Turn on and start recording
Stop recording and turn off
2
Turn on and start recording
Continue recording for 1 minute, then stop recording and turn off
3
Turn on and start recording
Continue recording for 10 minutes, then stop recording and turn off
4
Turn on and start recording
Do Nothing
5
Turn on
Stop recording (if recording), and Turn off
6
Turn on
Wait 1 minute (note camera may not be recording in this mode eg if using scripts), then stop recording (if recording) and turn off
7
Turn on
Wait 10 minutes (note camera may not be recording in this mode eg if using scripts), then stop recording (if recording) and turn off
8
Turn on
Do Nothing
-
What is your return/exchange/warranty policy?
A: We have a 15 day return policy for unused products. Product must be in original packaging and in new condition. For orders (over $1,500) and/or physically larger items (e.g. enclosures), a restocking fee of 10% will apply. Return shipping is the responsibility of the customer.
If the product is opened or used, the product can be returned within 15 days (except SD Cards and GoPro cameras which cannot be returned once opened). A 20% restocking fee will apply for refurbishing opened product. Return shipping is the responsibility of the customer.
If you are having trouble with the product, make sure you check our support area on the website for our Quick Start Guides and Product Documentation. Should you need additional help please contact support@cam-do.com however, please ensure you have submitted all of the information in the form first as our support team will ask for this information on our first reply email and it will save time: https://cam-do.com/search?type=page&q=ticket+support&view=search-support&submit=Search
Should you consider the product be faulty you can request to return the product within 6 months for our assessment. If the product is confirmed to be faulty by CamDo, return shipping costs will be refunded along with a full product refund (except SD Cards and GoPro cameras which cannot be returned once opened). Should the returned items be confirmed functional, a 25% restocking fee will apply to the refund. To initiate a return or exchange, please contact support@cam-do.com to receive an RMA number. Do not ship a product back to us without an RMA number. We will examine all returned items to confirm their condition and contact you regarding the status of your refund. Upon acceptance, please allow 2-3 weeks for the refund to process once the item is received.
We cannot support IT/wifi network/router/modem issues as there are too many variables. Please talk to your IT department/specialist/support team.
Any dismantling or modification(s) to CamDo products will void any warranty and cannot be returned.
GoPro products: HERO5 camera warranty issues are to be handled directly with CamDo. Any warranty issues with HERO6, HERO7, HERO8 and HERO9 cameras are to be handled directly between the customer and GoPro USA. Check out their warranty page here.
LumeCube products: Any warranty issues with LumeCube products are to be handled directly between the customer and LumeCube USA. Just email support@lumecube.com and they will take it from there. Check out their warranty page here.
Both GoPro and LumeCube are very responsive and is how their distribution model works - it is much quicker to get warranty response by emailing them directly.
EQUIPMENT PERFORMANCE LIMITATIONS
CamDo equipment is not fault-tolerant and not designed, manufactured or intended for use in extreme temperature or weather conditions, security surveillance, life support, emergency situations, hazardous or mission critical activities. You use CamDo equipment at at your own discretion and risk.
LIMITATION ON LIABILITY
The replacement warranty is as per the warranty section above. In addition, the replacement warranty is the whole and sole liability for the product. There are no other warranties, expressed or implied. Use of CamDo products confirms your agreement that CamDo Solutions Inc and its distributors will not be liable for any damages from or relating to CamDo Solutions Inc products. Please also note the Equipment Performance Limitations above.
Product Code: CDA01