SKU: 180268K
$890.00 USD
Our Solar Enclosures use a 9 Watt solar panel to recharge the included V44 battery. If your installation is in a particularly cloudy or rainy area we also have an 18W upgrade option for additional peace of mind.
Our outdoor enclosure is fitted with a sturdy aluminum mounting bracket that contains multiple ¼"-20 threaded holes on the top, back, and bottom for use with standard tripod screws. It also has 2 slots at the back for using straps to attach the enclosure to a pole. The solar panel is removable and attached to the top of the enclosure using a dual ball socket arm so it can be positioned for optimum sun exposure. The solar panel charges the included Lithium Polymer battery which outputs 5 volts to power the camera or other accessories in a weatherproof enclosure.
We also offer a sturdy swivel mount for easy mounting to a pole or flat surface, check out the product page here.
The enclosures are designed to be crushproof and dust tight. Inside the weather resistant enclosure contains an aluminum bracket designed to hold the GoPro camera, and CamDo Blink Time Lapse Controller. It is possible to access the SD card, or USB connector without removing the camera. If the camera needs to be replaced, the fit is extraordinarily tight, guaranteeing that the camera will be in the exact same position as before so there is no disruption to your time lapse footage positioning. The interior has space for extra batteries or other accessories such as our Motion Detector. The enclosure is fitted with a standard 67mm filter adapter and a neutral density UV optical glass “digital filter” is included. You can replace the filter with your filter of choice.
We also offer complete packs of equipment. Check out our packs page here.
Our case has several mounting options for different situations. There are two ¼” locking holes, one on each side of the case, through which a padlock, bolts, or threaded rods can be used to secure the contents of the box.
There are 2 slots on the back of the aluminum mounting bracket which allow it to be easily attached to a pole or structure using straps such as hose clamps or zip ties. The tripod screw holes at the back of the bracket can then be used to angle the camera.
We also offer a high quality swivel mount bracket that can be added to your system which allows fantastic aiming flexibility. Read more here.
The aluminum mounting bracket has multiple tripod screw holes on the top, back, and bottom that can be used with any standard photographic tripod or mounting bracket with a normal tripod thread (¼"-20). ¼"-20 bolts are easily obtained from any hardware store if you are making your own mount. There are hundreds of different compatible mounting brackets and magic arm brackets.
9 Watt Solar Panel
If your installation is in a particularly cloudy or rainy area we also have an 18W upgrade option.
Camera |
Compatibility ( Y / N ) |
HERO5 Black |
✔ |
HERO5 Session |
✔ |
HERO4 Black |
✔ |
HERO4 Silver |
✔ |
HERO4 Session |
✔ |
HERO (2014) |
✘ |
HERO3+ Black |
✔ |
HERO3+ Silver |
✔ |
HERO3 Black |
✔ |
HERO3 Silver |
✔ |
HERO3 White |
✔ |
HERO2 |
✘ |
HERO |
✘ |
Compatible with the GoPro HERO3, HERO3+, HERO4, HERO5 and Session cameras.
Which CamDo Solar System is right for my GoPro camera?
Our SolarX Enclosures are compatible with GoPro HERO3, HERO3+, HERO4, HERO5 and Session cameras. Refer Compatibility tab.
How do I setup my system?
View the Solar Power System set-up guide here.
How long does it take to charge the battery?
In direct sun, the V15 (4,000 mAH Lithium Polymer battery) will fully charge in approximately 5.5 hours using the previous 6W solar panel model. Our newer systems use a 9W solar panel option which can charge the included V44 battery typically in a day. Where it is particularly cloudy/rainy, we recommend our 18W upgrade option. The battery system incorporates protection against overcharging, over discharge, over current (short circuit), unusual voltage input, and temperature extremes.
Will the solar panel be able to keep my time lapse running indefinitely?
This would depend on the shooting cycle used and the sun exposure available in your location. We advise all customers to calculate their battery needs due to the many variables. We have a Time Lapse Calculator that can be used to help determine your ideal shooting interval and how long your battery should theoretically last using our controller boards and batteries. The Calculator also gives the rate at which the solar panel should be able to recharge your battery at your given location and with the panel angle that is used. Keep in mind that temperature, battery fatigue, and other electrical inefficiencies will prevent the camera from using the full battery capacity.
What is the original dust and water ingress rating of your enclosures? Can I submerge your SolarX or DryX enclosures?
The enclosures have an IP67 rating prior to installation of CamDo accessories. Our SolarX and DryX enclosures are not meant to be immersed in water.
How long will the battery last before it is discharged?
It depends on many factors including your latitude, the amount of sun and cloud during your shoot, the controller you are using, the camera you are using and the shooting schedule you have programmed. There are too many variables to give a perfect answer but we have created a Time Lapse Calculator to work out the best setup for your shoot in your location.
This uses our analysis of the power consumption of the various GoPro cameras and provides an explanation of how to calculate the theoretical battery life.
Practically, we have run the system indefinitely taking one picture every 15 minutes with the WiFi on, in Canada in the summer.
Why is "Always On" mode for batteries important?
Since our controllers turn the camera off between triggers to conserve power, Always On mode is important to prevent the battery from automatically turning off. Most of the USB battery packs on the market have an automatic power saving feature which turns off the battery if the battery is not constantly supplying power to a device. If the GoPro is powered off for more than a few minutes between triggers, the external battery might automatically shutdown due to inactivity. However, our V44 and V15 battery packs have two modes of operation, the standard Auto Off mode and an Always On mode. The Always On mode prevents the battery from automatically turning off when insufficient current is being drawn due to the camera being powered off.
Refer to our support page here to make sure you are in "Always On" mode when setting up your system. Refer Step 2 of the guide.
Make sure to disconnect the battery from all devices to check this. If you hold down the power button for at least six seconds and the charge indicator flashes 3 times and stays lit for a second or two, you are now in Always On mode. If you hold down the power button for six seconds and the charge indicator flashes 3 times and then goes dark straight away, you are in Auto Off mode.
How can I avoid condensation on the lens?
Our enclosures have an integrated auto-pressure valve that equalizes the atmospheric pressure difference to reduce condensation. The IP67 micro vent allows air to pass through while preventing water from entering. If you need additional protection against condensation, the extra space in the solar enclosure allows for one or more sacks of desiccant to be inserted in the box. For even more protection, there are some products available to coat the lens, such as those used on ski-goggles. The standard 67mm threaded lens filter can also be replaced with another 67mm threaded lens that already has anti-fog characteristics or coating.
TIP: Condensation is a result of humid air being sealed in the box when you close it and condensing when there is a temperature change. Try to close the box in as dry an environment as possible. If you need additional protection against condensation, the extra space in the solar enclosure allows for one or more sacks of desiccant to be inserted in the box. For more information, Google for avoiding condensation in underwater cameras, where the problem is discussed at length by many experienced photographers.
Can I lock the case?
There are two ¼” locking holes, one on each side of the case, through which padlocks, bolts, or threaded rods can be used to secure the contents of the box.
Is it possible to separate the solar panel from the box?
Yes. The solar panel is removable and has a 4ft charging cable that enters the enclosure through a waterproof cable gland at the bottom of the enclosure.
Can I mount the solar panel remotely from the enclosure?
Yes. However, if you need to place the panel remotely from the enclosure, attention must be paid to the gauge of wire used to connect the solar panel to the battery. The connectors on the solar panel cable are 3.5mm outer diameter, 1.1mm inner diameter barrel power connectors. So you'll need one end male (M3.5x1.1), the other one end female (F3.5x1.1). A local electronics store will have these connectors. We recommend using the largest cable that can physically fit into the particular connector you source to minimize voltage drop from the panel to the battery. The voltage drop must not exceed 0.5 volts. A 16 AWG or larger wire is recommended for distances exceeding a few feet.
Alternative 1" ball mount accessories such as our Tough Claw can be used to mount the solar panel away from the enclosure using the sturdy dual ball socket system.
Which cables and adapters come with the system and what do I use to connect the battery to the solar panel?
The system comes with all necessary cables along with a number of useful adapters for charging phones and other cameras as well as the cables used to charge the battery.
Refer to Our Solar Setup Guide.
Can I use this system to charge other devices as well?
Absolutely. The V44 battery pack can be used to charge any 5V device.
Can your systems be used for other purposes than GoPro cameras?
Yes. You can remove the GoPro mounting fixture to provide extra space for your equipment. The solar panel, battery, and enclosure can be used for your custom system or just used as a remote charging station for phones and other USB chargeable devices.
Does the enclosure O-Ring seal require special care?
The case is equipped with a hollow core EPDM gasket that has been designed to give superior performance and resist compressive deformation over time. To ensure a watertight seal, the gasket must be free of cuts, abrasions or tears. Debris or foreign material caught between the sealing rib on the bottom of the case and the gasket on the top of the case will prevent the case from sealing properly. A coat of an automotive type surface protector is recommended to help prevent dirt and debris from sticking to the seal. If the seal becomes damaged a replacement seal can be ordered from Cam-Do.com.
Special care should be taken to ensure that wires or cables do not get trapped in the door when it is closed. The power-claw latches can exert extreme force, resulting in damage to the cable and the O-ring seal.
General support can be found on our Support pages here.
The CamDo Blink or BlinkX controller boards are typically used with our Solar Enclosures to provide programming flexibility while significantly reducing power consumption. Information on these controllers can be found on the following pages:
BlinkX
Blink
Also, read the FAQ's tab for more information.
Product Code: HDR03 + PSP01
solarx-solar-kitThe SolarX-18W upgrade, adds an extra 9W solar panel to give you a total of 18W of power (2 x 9W panels). It comes with all necessary attachments (ball arm, socket) and wiring to get up and running in no time with your existing SolarX.
The SolarX outdoor enclosure is fitted with a sturdy aluminum mounting bracket that contains multiple ¼"-20 threaded holes on the top, back, and bottom for use with standard tripod screws. The SolarX-18W upgrade is simply attached to the bracket using the included ball mount and associated arm.
The solar panel is removable and attached to the top of the enclosure using the included dual ball socket arm so it can be positioned for optimum sun exposure.
The 2 x 9W solar panels charge the V44 battery (included in your SolarX) simultaneously so if one panel gets dirty or covered by shadow, the second panel will continue to work hard for your project.
$169.00 USD
Motion detection can be used for security camera applications, wildlife photography, and for recording events where a person or other object, such as a car or truck, moves past the camera from time to time.
The X-Band Motion Sensor does not work underwater.
Our X-Band Motion Sensor is an active device powered by BlinkX/Blink’s 3.5mm Port2 connection, which bounces 10.5Ghz microwave signals to determine if motion has occurred. Microwaves do not rely on heat so the moving object does not need to be warm to trigger the sensor. Microwaves will also pass through glass and plastic, so the X-Band sensor can be mounted behind a window or inside an opaque waterproof box for use outdoors. The range of the X-Band sensor is adjustable from 8 to 30 feet (2-10m). Actual distances will depend on the environment and mounting configurations.
The X-Band Sensor is typically used with our durable weatherproof SolarX or DryX enclosures that have enough space to house the GoPro, BlinkX/Blink, Motion Sensor, and Battery Packs.
Blink and BlinkX are designed to extend the GoPro camera's battery life by turning the camera off between triggers and allows for motion detection triggering to be set on a scheduled active time to ensure footage is only captured when needed. In power saving mode, since the camera needs to power on before starting the recording, there is approximately a 5 second delay between when the Motion Sensor is triggered and when the recording starts or the picture is taken. Where power is less of a concern Blink has a "fast capture" mode (currently in Beta for firmware v2.00) where the camera will continue to stay on during the active motion detection schedule to reduce the activation time to less than 1 second. The camera will remain off when no motion detection schedule is active.
The X-Band Microwave Motion Sensor is an accessory that can be combined with Blink or BlinkX to trigger the GoPro camera when motion has occurred.
Camera |
Compatibility ( Y / N ) |
HERO5 Black |
✔ |
HERO5 Session |
✔ |
HERO4 Black |
✔ |
HERO4 Silver |
✔ |
HERO4 Session |
✘ |
HERO (2014) |
✘ |
HERO3+ Black |
✔ |
HERO3+ Silver |
✔ |
HERO3 Black |
✘ |
HERO3 Silver |
✘ |
HERO3 White |
✘ |
HERO2 |
✘ |
HERO |
✘ |
Do I require Blink or BlinkX to use the X-Band Motion Sensor?
Blink or BlinkX is required to use the X-Band Microwave Motion Sensor accessory to trigger the GoPro camera when motion is detected.
How does the Motion Detection video recording time work if motion is detected more than once in the interval?
If the video mode is selected in the Motion Detector interface of Blink/BlinkX, the camera will continue to record for the amount of time set in the Video recording menu once motion is no longer detected. If movement is detected before the recording time elapses, the recording interval will be reset to ensure you capture the entire motion event.
How does the X-Band detect motion?
The X-Band sensor uses doppler detection of microwaves bounced off the object and is triggered by motion towards or away from the sensor. Microwaves pass through opaque plastics and glass, but not metal. The moving object does not need to be warm to trigger the sensor.
Will the X-Band Sensor work underwater if contained in a waterproof housing?
No. The X-Band Sensor only works in air and will not work underwater.
Can I use more than one sensor with Blink or BlinkX simultaneously?
No. Blink and BlinkX detect pulse frequency from the X-Band Sensor, so only one sensor can be used at a time.
Does the controller board fit inside the standard waterproof case?
BlinkX does not fit into any of the standard GoPro housings. Blink fits in the extended BacPac backdoor attachments included in the GoPro Backdoor Kit and provided with the GoPro accessories such as the GoPro Dive Housing, GoPro LCD BacPac or the GoPro Battery BacPac. However, since the Motion Sensor plugs into the 3.5mm port on the bottom of Blink, a small hole needs to be drilled into the housing to allow the sensor’s wires to pass through the housing. X-Band detectors are normally used with our outdoor SolarX and DryX enclosures.
CamDo offers a series of Outdoor Weather Resistant Enclosures designed to house the GoPro camera, Blink, and Motion Sensor along with space for a high capacity battery and optional solar panel for longer term deployment. The X-Band detector fits inside the weather resistant case and does not require any hole in the case for installation of the X-Band Sensor.
Can a Blink or BlinkX motion detection schedule and time lapse schedules overlap?
Yes, the motion detection can be set on a schedule that overlaps with a time lapse schedule. If the camera enters a time lapse interval while camera is currently recording in motion detection mode, the time lapse image will be skipped. If the camera is currently taking a time lapse image when motion is detected, Blink will re-trigger the camera on the motion detection schedule after the camera has taken the time lapse photo and turned off.
I am a hacker. Can I use the ports on the Blink or BlinkX board to trigger the camera using other devices?
The motion detection Port2 of Blink and BlinkX can be programmed to accept an external input to trigger an action. Unlike the X-Band operation which requires a set amount of pulses within a certain timeframe, PIR/External mode only requires a pulse for more than 250ms to trigger the camera. See this blog post for more details.
I am a not a hacker. I have an idea for a project for our organization. Can you help?
Yes. Our controller boards were originally designed to handle custom projects we built for scientists and professional photographers. Our controllers are very flexible and can be reprogrammed to respond to different kinds of control inputs. Some controllers also have an output which can be used to control lighting, or give different types of feedback. Contact us for a quote for your application.
General support can be found on our Support pages here.
BlinkX
Blink
Average GoPro recording times in each video setting (limited by SD card capacity)
Also read the FAQ's tab for more information.
Product Code: ASX01
$540.00 USD
ShootX is a purpose-built WiFi enabled time lapse camera with the option for automatic upload of images via the CamDo cloudX platform.
ShootX has multiple mounting connections and features a 120° wide angle lens to capture 2.6K resolution images. ShootX can be programmed for a single interval that repeats continuously. For increased programming flexibility without image upload features, see our BlinkX for the GoPro HERO5 cameras.
As can be seen from the graphics below, ShootX provides high quality 2.6K images and associated time lapse videos. It is significantly better than typical 1080 resolution and blows lower quality 720 cameras out of the water. If you need 4K footage, use our GoPro and BlinkX product offering.
Need to deploy your ShootX for extended periods? Achieve long term deployment with the ShootX Solar Kit. Featuring:
What is the ShootX field of view?
ShootX has a 120° wide angle lens that is focused from 60cm (2ft) to infinity. This provides a wide depth of field focusing everything in frame at least 60cm away from the lens.
What image file format does ShootX use?
ShootX outputs JPEG images with a configurable JPEG quality. Note that setting JPEG quality above 90 significantly increases file sizes and affects battery life. If battery life and memory capacity is important, we recommend retaining images quality at 90.
If I know approximately how long my project is, how do I determine the ideal interval between triggers?
The ideal shooting interval is normally determined by the length of the final time lapse video clip, capacity of the SD card or battery capacity available. Our Time Lapse Calculator can be used to help determine the ideal interval between photos as determined by these variables. Just select ShootX as your camera in the calculator.
Can ShootX be programmed to only capture images between set times on specific days?
Yes, ShootX can be programmed to take a shot at a regular interval between set times each day. You can't have a different schedule each day however. For greater programming flexibility, see our GoPro controllers; BlinkX for HERO5 Black and HERO5 Session, or Blink for HERO3+ and HERO4.
How do I change the interval between ShootX's image triggers?
The default interval between images is 10minutes. To adjust the interval, ShootX can be programmed from a web User Interface or connected to a PC or MAC via USB to edit the settings.ini
file using a standard text editor (eg. NotePad). See the ShootX User Manual for additional instructions.
Does ShootX have automatic image uploading via WiFi?
Yes, ShootX can connect to a WiFi signal to automatically upload each image to our cloud platform cloudX. See our CloudX page and ShootX User Manual for additional information.
What if I don't have a cloudX Pro subscription?
The photos will be stored on the camera, which you can download locally to a computer. You won't have access to the online cloud platform including features such as automatic upload, remote status monitoring, email notifications, remote firmware updating, etc.
Why is "Always On" mode for batteries important?
Since the camera turns off between triggers to conserve power, Always On mode is important to prevent an external battery pack from automatically turning off due to periods of inactivity. Most of the USB battery packs on the market have an automatic power saving feature which turns off the battery if the battery is not constantly supplying power to a device. If the camera is turned off for more than a few minutes between triggers, the external battery might automatically shutdown due to inactivity. However, our V15 and V44 have two modes of operation, the standard Auto Off mode and an Always On mode. The Always On mode prevents the battery from automatically turning off when insufficient current is being drawn due to the camera being turned off to conserve power.
How can I mount ShootX?
ShootX has two options for mounting, a standard threaded tripod insert (1/4"-20) on the bottom of the camera, and a vertical slot (24mm x 4.8mm) at the back of the camera.
We also have the ShootX mounting kit (see main tab).
What are the dimensions of ShootX?
ShootX is 75mm wide between each flat square surface and is 80mm wide between each of the flat triangular surfaces.
What does ShootX weigh?
ShootX weighs 300g. This compares to a GoPro HERO5 Black camera at 117g or the GoPro HERO5 Session at 74g.
General support can be found on our Support pages here.
Also read the FAQ's tab for more information.
Product Code: CMR001
$50.00 USD
CloudX is a state of the art online time lapse platform, allowing you to monitor your time lapse camera remotely.
If you have purchased the CamDo Blink or BlinkX scheduler, you can login for remote status monitoring of your devices. View a list of heartbeat status for each day confirming:
There is also flexibility in setting up multiple email addresses and a schedule of how often the daily status information should be emailed to you.
In order to use this feature, Blink/BlinkX must be near a WiFi access point with an internet connection(either an open WiFi network or WPA secure network - WEP secure networks are older technology and not supported).
If you have purchased the CamDo ShootX camera or UpShot (coming soon), you can also upload your images to the CloudX and get updated time lapse videos automatically created!
With every purchase of a compatible CamDo product (Blink, BlinkX, ShootX), you get two weeks free access to CloudX.
All you need to do is enter your details into the user interface for your particular product (see the instructions for how to do this on our support pages here) and your free account will be automatically created. You will then automatically receive an email with your account details and how to login.
For continued access, CloudX requires a subscription. The options, features and pricing are as follows:
Two weeks free is included with all compatible CamDo products so you can try it out. For the 12 month Pro Plan, get 12 months access and only pay for 11 months.
Feature/Pricing |
CloudX Lite Plan |
CloudX Pro Plan |
Status Heartbeat |
✔ |
✔ |
ShootX compatible |
✘ |
✔ |
Blink/BlinkX compatible |
✔ |
✘ |
Daily Email |
✔ |
✔ |
Image Upload |
✘ |
✔ |
Cloud Storage |
✘ Status history only |
✔ 15 GB storage |
Automatic Time Lapse Creation | ✘ |
✔ Once per week |
3 Months Access | $50 | $267 |
12 Months Access | $150 | $879 |
If you need more frequent uploads or larger storage, please contact sales@cam-do.com for pricing.
The platform is compatible with CamDo's very own camera ShootX and GoPro cameras connected to BlinkX (for HERO5Black and HERO5Session) or Blink (for HERO3+ and HERO4):
Compatibility with devices is as follows:
Device |
CloudX Lite Plan |
CloudX Pro Plan |
ShootX compatible |
✘ |
✔ |
Blink/BlinkX compatible |
✔ |
✘ |
ShootX - purpose-built timelapse camera from CamDo. Capture months on one charge or indefinitely with a small solar panel. Upload footage and heartbeat status information. One button operation. Auto time-lapse generation.
Blink and BlinkX - time-lapse controllers for GoPro cameras.
Additional features we are working on:
Camera |
CloudX Heartbeat |
CloudX Upload |
✔ |
✔ |
|
✔ |
✘ | |
✔ |
✘ | |
UpShot |
coming soon |
coming soon |
Will BlinkX ever have the upload feature?
No, however, we have a new product called UpShot that will be released in Q4 2018.
Can I change the settings of the camera remotely?
No, only update the firmware. This is likely to be a future feature.
General support can be found on our Support pages here.
Also read the FAQ's tab for more information.
Product Codes: Lite - SCS05 (3month) / SCS09 (12 months)
Pro - SCS07 (3month) / SCS08 (12months)
Item | Price | Qty | Total | |
---|---|---|---|---|
Subtotal |
$0.00 USD |
|||
Shipping | ||||
Total |